For my best friend Doug Abbott. 1951 to 1999
♫ ♪ Lay down your weary tune, lay down. Lay down the song you strum. And rest yourself 'neath the strength of strings. No voice can hope to hum ♫
I was 11 years old when I first heard the Beatles. By the time I was 12 there was no question about it, I had to have a guitar. I was fortunate. Dad bought me a very used Stratocaster for $150 USD. I saved up $200 to by a Fender Deluxe Reverb amplifier.
Silvertone amplifiers were the next choice. Looking back, there were some other fine amplifiers that were probably in the same price that came with finer construction, but a Silvertone amplifier was so accessible. The inner working may have been slightly different, but they were well made.
Sears catalogue in the mail. Some lucky folks got both Sears and Montgomery Wards catalogs.
My friends and I would head right to the guitar advertisements that promised, “a professional sounding instrument made of the finest birch.” The electric guitars were generally made by Harmony, Valco or Kay.
Of course we all wanted the biggest and loudest amplifier we could afford.
Silvertone came through, although there were some quality issues.
The electronics were fine. The reverb sounded a little tinny, considering it was housed in the amplifier. Other than that it was a great amp, especially for the money.
used particle board to construct its cabinets while Fender used white pine. The other issue was the speaker baffles were constructed of ¼” masonite boards.
The covering used on most Silvertone amplifiers was merely inexpensive gray and black fabric that easily was damaged if the amplifier was knocked against a corner.
Frequent bumps and knocks damaged the particle board. These amplifiers were purposely made on the cheap to be affordable to everyone.
However the electronics in the Twin Twelve amplifiers did not seem to be adversely affected by the cheap cabinet design.
the tube bass amps. The speaker rattled like crazy. Tightening the nuts and screws on the basket did help a little. Possibly the best fix was to remove the particle board and replace it with solid wood.
Today what amazes me is the amount of money these old amps are commanding.
model 1484. This amplifier came with a speaker cabinet that was slightly smaller than a 1963 Fender Bassman or Bandmaster.
two 12” 8 ohm Jensen speakers wired in series. In the bottom of the cabinet there was a space to store the separate amplifier unit for travel.
two inputs. Each channel came with knobs for volume, bass and treble. As true with Fenders of that era, one channel had no effects and the other was connected to the reverb and tremolo.
The tube complement consisted of 2 - 6L6GC power tubes, 2 - 6CQ7 – one was the phase inverter and the other was the reverb driver – 3 - 12AX7 preamp tubes and another 12AX7 for the tremolo circuit. The rectifier was solid state.
Because of the voltages on the power tubes, Fender amps were much cleaner than Sears amps, however these Silvertone models deliver a nice compressed sound.
The Bass and Treble controls are interactive with the volume. The higher you turn up the bass and treble produces more gain this amplifier produces.
turn the reverb potentiometer all the way up. This produces some other-worldly stuck in a cave sounds.
In 1963 and 1964 you could buy a 1484 Twin Twelve for $149 USD.
a complement of ten tubes. I saw two websites stating it had 5 rectifier tubes, which I find hard to believe.
From looking at a schematic I know the amp had 4 6L6GC power tubes team up in pairs and 2 6CQ7’s.
One was the phase inverter and the other was the reverb driver. That left 4 12AX7 tubes, 3 of which were preamp tubes and the 4th took care of the tremolo circuit.
In 1965 the Silvertone 1485 amplifier could be yours for $239.95 USD.
My thought is Sears/Danelectro wanted to keep the sound down to prevent speaker rattle, which is just what happened to my friends amplifer.
1483 Silvertone Bass Amp was a two channel amplifier with two inputs for each channel. The channels were identical and there were no effects. The tube complement included two 12AX7 preamp tubes – one 6FQ7 phase modulator – one 5Y3 rectifier tube and 2 6L6GC power tubes.
The controls were volume, treble, bass for each channel. The switches on the front were standby / operate, the all important ground switch and an on/off switch.
In 1963, wall outlets accepted only electric cables with two prongs of equal size. A guy could get a shock if he touched a microphone connected to a P.A. with reverse polarity. The biggest issue was 60 cycle hum through the amplifier. The ground switch prevented both situations. Despite being called a ground switch, it really did not 'ground' the amplifier.
The speaker was mounted on the left side of the cabinet and the storage area for the amplifier was on the right side and the amp head was stored vertically.
$99 USD for the amplifier and $79 for the guitar. My dear friend Doug went crazy due to the rattling speaker, so he replaced it with a Utah speaker. Then saved up and bought a JBL Lansing speaker. He then stuffed the back full of fiberglass insulation. He finally saved up enough for a Fender Bassman.
In my opinion the 1483 would have made an excellent guitar amp as it produced as much power as a Fender Deluxe, only the Sears amp used 6L6 tubes instead of 6V6’s.
Silvertone 1474. This amplifiers circuitry was similar to the 1484, however it was a combo amp and was made by Danelectro.
In fact it was similar to an amplifier Danelectro sold under it's own brand called The Twin Twelve.
The amp included twin Jensen special design speakers, two channels; one clean and one with effects. Each channel had a volume, treble and bass control. The 1474 came with a Hammond reverb unit and tremolo. It produced 50 watts from 2 6L6GC power tubes.
While the model 1484 came with grey and black fabric covering, the model was 1474’s covering was solid black with white piping around the front of the cabinet.
It sold for $139.95 in 1961 and only was offered for one year.
This amp produced 5 watts of power into an eight inch Jensen speaker.
It came with a volume and a tone control. This model sold from 1961 to 1962.
The Silvertone 1482 was similar to the 1472, except it offered 15 watts of power. The key difference was the extra 5 watts and the handle on the top was flexible, while the handle on the 1472 was solid and known as a ‘refrigerator handle.’
The 1482 was offered in 1963 through 1968. It too came with a Jensen 12 inch special design speaker. Both amps sold for around $69 USD.
The final Silvertone amplifiers that were very popular in the 1960 decade were the amp-in-a-case models.
Silvertone offered two models in the 1960’s; four if you considered the value of the guitar that came with it.
models 1448 and 1457. Both were made by Danelectro.
The wooden guitar cases came with a section of gray grill cloth which hid a tiny 3 watt tube amplifier with a five inch speaker. The speaker frame was designed to prevent damage to the speaker.
The 1457 model contained a twin pickup Dano guitar, a volume and tone control, tremolo knobs, cord, footswitch and a 45 rpm ‘how to play the guitar’ record.
Prior to the introduction of the 1457, the model was designated the 1449. The 1449 was first made available in 1963 and replaced by the 1457, which was essentially the same amplifier and guitar.
The 1448 sold from 1962 to 1965 and the 1457 sold from 1964 to 1966 when both were replaced by the model 1451.
The Silvertone/Danelectro model 1452 came with an 8 inch speaker, 5 watts of power, 4 tubes and a Danelectro solid wood guitar with two lipstick pickups and a tremolo bar. The 4 amp controls supported volume, tone and speed and depth for the tremolo.
The amplifier unit was housed in the guitar’s case. It produced 3.5 to 4 watts of power through a rectifier, power and preamp tube. The speaker was 6 and a half inches. The only control was volume with a chicken head knob.